Skip to content
Industrial gas detection for demanding environments
Safety technician inspecting process equipment at a chemical facility

Industry

Gas Detection for Chemical Plants

Gas detection in chemical plants starts with the substances handled and the conditions in each process area. Toxic releases, flammable solvent vapors and oxygen displacement during nitrogen use require different measurements. The guide below connects these hazards to monitoring tasks and equipment, so you can discuss your requirements with Eranntex before selecting a model.

Gas detection by chemical process area

Each process area presents a different set of potential releases. Use the table to connect the chemicals handled in that area with a monitoring task and a starting point for equipment selection.

Chemical process areas, gas hazards and monitoring guidance
Process area or taskGas hazards to assessMonitoring guidance
Chlorine and hypochlorite storage, feed and dosingChlorine (Cl₂) and hydrogen chloride (HCl); chlorine can also be released if acid contacts hypochloriteArea monitoring
Ammonia storage, refrigeration and reactor feedsAmmonia (NH₃)Area monitoring
Solvent storage, tank farms, loading and unloadingFlammable solvent vapors (%LEL), toxic vapors and reaction products from incompatible chemicals mixed during transferLeak detection
Nitrogen inerting, vessel entry and maintenanceOxygen deficiency, flammable vapors, residual toxic gases from the process, and gases released when equipment is openedConfined space entry or personal gas monitoring
Hot, wet or remote process streamsProcess-specific gases that need to be assessed in an extracted sampleGas monitoring and analysis systems

Use your chemical inventory, safety data sheets and credible release scenarios to determine which gases to monitor. The examples above are starting points for that assessment.

U.S. exposure limits for chemical-plant gases

For U.S. projects, OSHA permissible exposure limits (PELs) are enforceable exposure limits. NIOSH publishes recommended exposure limits (RELs) and immediately dangerous to life or health (IDLH) values. Use the table to review these references for four gases encountered in chemical processing.

U.S. general-industry exposure reference values
GasOSHA PELNIOSH RELIDLH
Chlorine (Cl₂)1 ppm ceiling0.5 ppm ceiling (15 min)10 ppm
Ammonia (NH₃)50 ppm TWA25 ppm TWA; 35 ppm STEL300 ppm
Hydrogen sulfide (H₂S)20 ppm ceiling*10 ppm ceiling (10 min)100 ppm
Hydrogen chloride (HCl)5 ppm ceiling5 ppm ceiling50 ppm

*OSHA general industry permits one H₂S peak up to 50 ppm for up to 10 minutes only if no other measurable exposure occurs during the 8-hour shift. Values checked October 26, 2026.

TWA means time-weighted average: OSHA uses an 8-hour shift, while NIOSH RELs use up to a 10-hour day during a 40-hour week. A STEL is normally a 15-minute average. IDLH values describe an immediately dangerous atmosphere and are not acceptable operating concentrations.

Exposure limits are not automatic alarm setpoints. Select alarm levels as part of the site hazard assessment, together with the required response. In the DuPont La Porte investigation, the CSB found detector alarms set well above safe worker exposure limits. The case shows why alarm settings and the response they trigger need to be assessed together.

Selecting fixed, portable and extractive equipment

Fixed detectors monitor selected locations around process equipment, while portable instruments support personal monitoring, pre-entry testing and leak investigation. Extractive systems bring a sample from the process to a monitoring system. Choose the approach for each task, then review the required gases, sampling conditions and outputs.

The GTYQ-MIC-600 fixed multigas detector is configurable for one to six gases and provides a local display in an IP66 enclosure. Standard RS485 Modbus RTU and three-wire 4–20 mA outputs support integration with a receiving controller or DCS; HART 5 is optional. Review the required gases and outputs against the proposed configuration.

The MS400-S portable multigas detector has a built-in pump for remote sampling and can switch to diffusion sampling. Standard configurations cover one to four gases, with expanded configurations for up to six. For pre-entry testing or leak investigation, specify the gases, sampling accessories and operating conditions.

The TH-2000-C sampling and monitoring system combines extractive sampling and conditioning for hot or humid process gases. Documented conditioning includes electronic cooling, moisture removal, filtration and drainage. Share the sample composition, temperature, moisture and sampling route so the project configuration can be assessed against the target gases.

Discuss your chemical-plant monitoring requirements

You can start an inquiry before choosing a model. Share the details available for each monitoring point or task, and our engineers can review equipment options with you. The information below helps identify the remaining specifications to confirm.

  • Target gases and measuring ranges: name the substances, the required range for each gas, and which gases must be monitored together.
  • Process area and release scenario: describe the operation and potential leak sources, and include a site layout if available.
  • Operating and sample conditions: include temperature, moisture and pressure, plus the sampling route and any known background gases.
  • Outputs and receiving equipment: describe the connection required by your controller, PLC or DCS, including any specified protocols or alarm contacts.
  • Area classification and power: state the hazardous-area classification (Class/Division or Zone) and the required approvals. Provide the available AC or DC voltage and, where applicable, the frequency and number of phases.

Gas detectors for chemical plants

Related guidance

ENGINEERING GUIDEHow to Define an Industrial Gas Leak Detection Project
Read guide
CHECKLIST & TOOLSGas Detector Quotation Preparation Checklist
View checklist

Common gas detection questions

XML 地图